As tile and grout cleaning moves from low tech to high tech, more carpet cleaning companies are finding tile and grout cleaning to be more profitable than carpet cleaning.
This untapped market produces returns from 50 cents to $1.50 per square foot and all you need are a few tools and chemicals that work with your existing truckmount and portable. However, many carpet cleaners are reluctant to get into this business, mainly because they are not sure how to perform the service. They’re afraid that they will ruin something, and while these fears are understandably true, a little education can quickly overcome your fears.
1. Does the tile pattern repeat? In a large room you would see the man-made tile repeated in a combination of four to six different tiles. With natural stone, every tile would be different and has the 1/16th beveled edge. Tile manufacturers are making more and more look-a-likes that try to duplicate real stone in every way, which makes this task even more difficult. Don’t be alarmed. Efflorescence Cleaner Just visit your local flooring store to learn to tell the difference visually. A trained eye can usually determine whether it’s man-made or natural by sight alone. Scott Rendall, of BRC Systems and owner of Sci-Clean in Brighton, MI, says good inspection is most important and suggests looking for chips or broken tiles. “Make sure grout is intact, he said. “When cleaning marble or other natural tiles, don’t use acid because it will etch the surface.” If the tile pattern repeats, then it’s man-made. The following three tests are necessary only if you haven’t determined this from the previous test.
2. Determine surface porosity Placing a few drops of water on the tile. Some tiles will show an immediate absorption of water. There’s a range of porosity and even the most dense stone-like granite will allow water to flow through it, even though it could take more than 10 minutes to fully penetrate the surface and more than 30 minutes to work through the whole tile. Most ceramic tile is relatively non-porous. The more porous the tile, the more prone the tile is to efflorescence as a result of cleaning. You may notice some efflorescence, a precipitate that has the appearance of a white, chalky, powder-like substance on the surface of the grout and most porous tiles, especially darker tiles. A free demonstration is a great way to sell customers on tile cleaning. To remove it, allow adequate drying time for the minerals to accumulate completely to the surface of the grout or tile, then buff it out using an abrasive pad or brush.
3. Scratch the tile Scratch the surface of the tile with a sharp knife. Make sure you ask for permission, since you wouldn’t want to replace the tile at your expense. Find an inconspicuous area where you are going to test or get a piece of extra tile. If the stone scratches, high pressure may not be the ideal cleaning method. If caution is taken to make sure no dirt gets trapped under the tools being used, then these tools can be used at lower pressures. The softer the tile, the lower the pressure.
4. Apply phosphoric acid If it fizzes, then the tile is natural. In the beginning, you will avoid natural stones, but if you test first, then you can successfully clean even the softest of stone tiles. Grout concerns The problem with grout is that each time tile is mopped, dirt gets pushed down into the grout lines, making it several times dirtier than the tile.
Efflorescence is a white, chalky substance that can be buffed off using an abrasive pad or brush in the dry state. “We have found two things to work well on grout,” Melody Price, sales manager for Magic Wand Company, said. “One is a concentration of high pressure and the other is a tile safe bleach product.” The pressure is necessary to get into the small opening of grout to blow out the dirt. The oxygen bleach is necessary to bleach away years of dirt that have been absorbed into the grout. The key is the dwell-time with this product; the dirtier the grout, the longer the dwell time. It is important to keep the area wet while the chemical is allowed to work.
High pressure tile cleaning can have dramatic results. Most grout will come clean, but if it still looks “blotchy” Price recommends repeating the application of the oxygen bleach to give it another opportunity to get absorbed in the grout that it did not get earlier because of the build up. As a last resort, use one to 10 parts of muriatic acid. Apply it with a towel on the grout only, and rinse it out within two minutes. You can increase the concentration if the grout does not respond. Only use this on cementitious grout.